Gear Service

Drivetrain wipe and re-lube, inspect chain/sprockets and derailleurs for wear or damage and quote for replacement parts needed, cables lubricated, stop adjuster screws reset, cable tensions adjusted and gears realigned.

Brake Service

Brake component wipe and re-lube, inspect all brake parts for wear or damage and quote for new parts as necessary, cables lubricated, spring tensions reset, brakes realigned, braking surfaces degreased.

Just fix my bike

Get your bike assessed and then receive a quote.

Safety Check

Recommended for a bike that is suspected to be in good working order but you would just like an expert eye (and allen key) cast over it to be sure. Inflate and check tyres for wear/damage, frame and major component wipe and inspect for wear/damage, note any worn or damaged parts and quote for replacements, bolt check wheels/handle bars/pedals/brake parts/gear parts.

Kids Bike Service

A basic service is recommended every 6 Months.

Standard Service

Our 'Standard Service' is recommended every 6 to 12 Months. Designed to give your bike a good tune up without breaking the bank! Your bicycle will be expertly checked, adjusted, and set up to perform as well as it can without major disassembly (wheels are usually removed to check/adjust hub bearing play and safety of fastenings).

Full Service

A 'Full Service' is recommended every one to two years or if your bike needs a thorough strip down and re-build.

Cut down handlebars

Cut a specified amount from each end of handlebar

Service / replace bottom bracket (as part of service)

Removal and re-fitting of bb parts (includes clean and re-grease as well as any bearing retainer or compound required) Price is 'from' £25 , (priced as an addition to full or standard service) some systems take longer and will be priced accordingly - please ask for info.

Build new bike from box

Assemble, setup and pdi new cycle from box. Price from £75

Tubeless Tyre Conversion Pair

Convert pair of wheels / tyres to tubeless Includes Muc-off Valves, tape and sealant.

One Hour Labour

One hour of labour time

Hydraulic brake bleed pair

Bleed one pair of hydraulic brakes

Fit New Internal routed cable

Fit a new cable internally routed through frame. Gear, brake or dropper cables. Cable charged as extra.

Labour charge 1/2 hour

Half hour of workshop labour

Service Headset - (as addition to standard or full service)

Service or replace headset bearings

Brake Burp (shimano or similar)

Burp air from top of shimano type hydraulic brake system (not full bleed)

Bike Clean (as addition to service)

This option is the same as our normal Bike Clean but at a reduced price to be sold in addition to a 'Service' (either 'Standard' or 'Full')

Replace handlebar stem

Remove and refit handlebar stem Internal cable routing and or other complications will incur extra charge.

Fit internal cable (as part of service)

Fit a gear, brake or dropper cable that runs internally through frame, fork or handlebars etc. This option/price is 'as part of a service' if job is on its own please select another option.

Bicycle Build from box

Build or setup your brand new bike - Cost starts at £75 but may be more for some bikes - please ask.

Service or replace Bottom Bracket

Removal and re-fitting of bb parts (includes clean and re-grease as well as any bearing retainer or compound required) Price is 'from' £40 - some systems take longer and will be priced accordingly - please ask for info.

Service or replace Headset

Service or replace headset bearings Priced 'from' £40 - some bikes will incur further cost due to internal cable routing or other complications - please ask.

Hydraulic Brake Bleed single brake

Bleed one hydraulic brake

External Brake or Gear Cable Fit

Does not include price of parts. Use 'with service option' for reduced price as part of 'Standard' or 'Full' service.

Wheel True

Remove wheel and true in stand. Replace up to 10 spokes (spokes priced separately).

Service / replace rear suspension linkage bearings

Disassemble rear suspension linkages and service or replace bearings. Priced as ‘from’ £60 more complicated or damaged parts will be quoted accordingly.

Service Hub - Single

Service single hub. Strip, clean and regrease. Pressed in bearings will only be removed if replacement is required, otherwise hub will be disassembled as much as reasonably possible.

Software Update & Diagnostic Report

Shimano systems only

Tyres Inflated to Correct Pressures & Inspected for Wear

Wheel Build - Single

Cost is 'from' £60 - some variations will incur additional costs. Parts not included.

Cassette Replacement & Fit

Chain Replacement & Fit

Derailleur Hanger Straightened

Please be aware that mech hanger may break during this process - it is inherently risky. Ask for details if unsure.

Fit Handlebar Tape

Tape charged at extra cost. Reduced labour charge if tape bought in our shop.

Hub Service

Strip, clean, regrease and reassemble hub front or rear. Parts are quoted separately. Press fit bearings are generally only removed if replacements are required.

Inner tube fitting

Remove tyre, replace inner tube and refit tyre. Removal and refit to bike may incur extra cost.

Drill valve hole to larger size

Usually drilling presta valve holes to schrader size. Removal and replacement of tyres / wheels will be charged separately.

Hub Service - as addition to full or standard service

Strip, clean, regrease and reassemble hub front or rear. Parts are quoted separately. Press fit bearings are generally only removed if replacements are required.

Tubeless tyre fitting (parts charged separately)

Fit one tyre on one wheel using either customer supplied parts or charge parts separately.

Bike Clean

Bike Clean - as addition to service

Tubeless Tyre Conversion Pair

Convert pair of wheels to Tubeless Includes Muc-off valves, sealant and tape

Fork Lower Leg (50 hour) Service

Remove lower legs clean and reassemble. Wiper seals can be replaced during this service (parts priced separately). Grease and fork oil is included.

Air can service

Service air can , rear air spring suspension. Remove shock, remove air can, clean internally , replace seals if required , lube and reassemble/refit. Parts charged separately.