Torque Collective

Collection Booking Pre-Payment Configuration

Drop-off Booking Pre-Payment Configuration

Assessments 

Not sure what your bike needs? Book a workshop assessment and we’ll check the bike, identify the priorities and give you a clear quote before any work starts.

Ideal for bikes with unknown issues, overdue servicing, brake problems, drivetrain noise, play, creaks, poor shifting or general setup concerns.

If you go ahead with service work over £100, the £25 assessment fee is deducted from the final bill.

Bike Health Check / Workshop Assessment

Fork or shock feeling harsh, sticky, noisy or overdue? Book a suspension health check and we’ll inspect the condition, check setup and advise what service it actually needs.

We’ll look at visible seal condition, stanchions, shock shaft, basic function, setup, pressures where relevant and likely service requirement.

Ideal if you are unsure whether you need a lower leg service, air can service, full service, or setup adjustment.

If you go ahead with suspension work over £100, the £25 assessment fee is deducted from the final bill.

Suspension Health Check

Wheel Building and Maintenance

A professional tyre fitting service for a single wheel, ensuring correct installation, seating, and safe operation.

Whether replacing a worn tyre or fitting a new one, this service ensures the tyre is installed properly and ready to ride.

What’s Included:
Removal of existing tyre
Installation of new tyre
Correct seating and inflation
Basic safety and fit check

Important Information:
Price is per wheel
Labour only — tyres, tubes, tubeless sealant, and valves are not included
Tubeless setup or sealant refresh is not included and charged separately
Rim tape replacement is not included and will be charged if required
Any additional work will always be discussed before proceeding

A straightforward service, done properly — safe, secure, and ready to ride.

Tyre Fit (Front or Rear)

A professional tubeless setup designed to improve puncture resistance, ride feel, and overall reliability.

This service ensures tyres are correctly installed, sealed, and set up to manufacturer recommendations for consistent, dependable performance on the trail or road.

What’s Included:
Removal of existing tubes (if fitted)
Installation of tubeless valves
Tyres correctly seated and sealed
Tubeless sealant added to both tyres
Leak check and initial pressure setup

Important Information:
Price covers both wheels
Standard tubeless valves and sealant are included
Suitable for tubeless-ready rims and tyres only
Rim tape replacement is not included and will be charged separately if required
Any additional work or parts will always be discussed before proceeding

A clean, reliable tubeless setup — fewer punctures, better grip, and more confidence on every ride.

Tubeless Setup (2 Wheels)

A comprehensive wheel truing service for wheels requiring significant correction, tension balancing, or recovery from poor alignment.

This service addresses both lateral and radial deviation, restoring proper spoke tension, structural integrity, and overall ride quality.

What’s Included:
Lateral and radial truing
Full spoke tension assessment and balancing
Spoke inspection for damage or fatigue
Final trueness and structural check

Important Information:
Suitable for wheels with visible wobble or uneven tension
Broken spokes, rim damage, or nipple replacement are not included
If additional parts or work are required, these will be discussed before proceeding

Restores strength, stability, and confidence — not just a straight wheel, but a properly balanced one.

Wheel True – Major

A precision truing service for wheels with minor deviations, designed to maintain smooth running and prevent issues from developing further.

This service focuses on small lateral or radial corrections, ensuring the wheel runs true and tension remains balanced.

What’s Included:
Minor lateral and radial truing
Spoke tension checked and equalised where possible
Final trueness and function check

Important Information:
Suitable only for wheels with no broken spokes or structural rim damage
If additional correction or tension work is required, the service may need to be upgraded to a Major Wheel True
Any additional work will always be discussed before proceeding

A small correction done at the right time — keeping your wheel running smoothly and preventing bigger issues later.

Wheel True – Minor

Please edit your services to reflect what you offer and fully customise the description and prices accordingly. If you operate less than three levels of service, please look at our pre-selected items, and decide what level your services match. You can remove a level by simply unticking it.

Service Packages

Not sure exactly what your bike needs? Book an Assessment & Inspection and let our expert technician carry out a thorough evaluation of your bike, components, or suspension system.

We’ll provide a clear, honest breakdown of any issues found, explain the work required, and recommend the most effective solution—whether that’s a simple adjustment, routine servicing, or more in-depth repairs.

This service is ideal if you're experiencing a problem but aren’t sure of the cause, or if you'd simply like a professional check-over before committing to further work.

Please note: If you proceed with the recommended repair or service work, the cost of your assessment will be deducted from the final labour charge.

Assessment & Inspection

A 6-month service designed to keep your e-bike running smoothly, safely, and performing consistently between full services.

This is not a basic check-over. It’s a structured service focused on drivetrain performance, braking reliability, and overall system safety — including key checks specific to e-bikes such as motor area inspection and electrical system condition.

What’s Included:

Core Safety & System Checks:
Full bike safety inspection (frame, components, key wear points)
Motor area, battery mount, and wiring visually inspected
All critical bolts checked and torqued correctly
Headset inspection and adjustment

Drivetrain Performance:
Gear indexing and adjustment
Chain inspection and lubrication
Derailleur alignment check
Drivetrain performance optimisation

Braking System Setup:
Brake inspection and performance check
Calliper alignment and adjustment
Lever setup and bite point optimisation
Pad and rotor condition inspection

Wheels & Tyres:
Wheel trueness check and minor adjustments
Tyre condition and wear inspection
Tubeless system check and sealant top-up

Clean & Finish:
Drivetrain clean and re-lubrication
Full wipe-down and final inspection

Important Information:
This service does not include brake bleeding, suspension servicing, or internal bearing work
Any worn components or additional work will be identified and discussed before proceeding

Designed to keep your e-bike running properly between major services — consistent, reliable, and ready to ride.

Interim Service - E-MTB

Clean and inspect seat post and clamp. Grease/fibre grip as appropriate

Saddle

Clean and insect saddle rails/clamps. Adjust position if needed

Check saddle for wear/damage

Ensure any accessories are safe/secure

Accessories

Inspect fork for damage/wear including dropouts, main tubes, crown, steerer tube and accessory mounting points

Frame/Fork

Inspect headset for wear/corrosion, adjust

Handlebar/Headset/Stem

Inspect handlebar for wear/damage, check torque

Inspect/adjust hub bearings for wear/damage, ensure smooth movement/no play

Wheels/Tyres

Inspect spoke tension and true lateral/radial as appropriate

Inspect tubeless system, top-up or replace consumables as appropriate

Inspect condition of hose/cable

Brakes (Brake & Pad Type)

Inspect caliper for correct function including clean/lube pistons

Inspect brake rotor for wear/damage/torque

Inspect chain rings/crank arms/spindle for wear/damage

Bottom Bracket/Cranks

Inspect pedal body for wear/damage

Pedals

Inspect chain for wear/damage lubricate

Drivetrain/Gears

Inspect rear derailleur cable/electronic wire for wear/damage

Set rear derailleur upper/lower limits and b-tension

Inspect front derailleur for wear/damage

Set front derailleur upper/lower limits

Suspension forks, clean/inspect seals and upper tubes. Check for function

Inspect stem for wear, check/adjust torque, straight

Inspect handlebar tape/grips for wear/damage

Inspect spokes and rim for wear/damage

Inspect tyres for condition and wear

Inspect condition of lever, including main body, blades and position. Adjust if required. 

Inspect condition of brake pads

Inspect condition of hydraulic fluid if applicable

Adjust brake, ensure correct function including no rub and appropriate bite-point

Inspect bottom bracket torque, ensure free rotation of bearings

Ensure smooth rotation of pedal bearings and check for play

Inspect cassette for wear/damage and torque

Ensure derailleur hanger is straight and secure

Inspect rear derailleur for wear/damage

Adjust rear derailleur indexing

Set front derailleur position/height

Adjust front derailleur indexing

Inspect frame for damage/wear including dropouts, main tubes, seat clamp area, bottle cage and accessory mounting points

A 6-month service designed to keep your bike running smoothly, safely, and performing consistently between full services.

This is not a basic check-over. It’s a structured service focused on drivetrain performance, braking reliability, and overall bike condition — ensuring everything is correctly adjusted, lubricated, and working as it should.

What’s Included:

Core Safety & Inspection:
Full bike safety inspection (frame, components, key wear points)
All critical bolts checked and torqued correctly
Headset inspection and adjustment

Drivetrain Performance:
Gear indexing and adjustment
Chain inspection and lubrication
Derailleur alignment check
Drivetrain performance optimisation

Braking System Setup:
Brake inspection and performance check
Calliper alignment and adjustment
Lever setup and bite point optimisation
Pad and rotor condition inspection

Wheels & Tyres:
Wheel trueness check and minor adjustments
Tyre condition and wear inspection
Tubeless system check and sealant top-up

Clean & Finish:
Drivetrain clean and re-lubrication
Full wipe-down and final inspection

Important Information:
This service does not include brake bleeding, suspension servicing, or internal bearing work
Any worn components or additional work will be identified and discussed before proceeding

Designed to keep your bike running properly between major services — smooth, reliable, and ready to ride.

Interim Service - Analog MTB

A 6-month service designed to keep your bike running smoothly, efficiently, and reliably between full services.

This is not a basic check-over. It’s a structured service focused on drivetrain efficiency, braking performance, and overall bike condition — ensuring everything is correctly adjusted, clean, and operating as it should.

What’s Included:

Core Safety & Inspection:
Full bike safety inspection (frame, components, key wear points)
All critical bolts checked and torqued correctly
Headset inspection and adjustment

Drivetrain Performance:
Gear indexing and adjustment for smooth, precise shifting
Chain inspection and lubrication
Derailleur alignment check
Drivetrain performance optimisation

Braking System Setup:
Brake inspection and performance check
Calliper alignment and adjustment
Lever setup and feel optimisation
Pad and rotor condition inspection

Wheels & Tyres:
Wheel trueness check and minor adjustments
Tyre condition and wear inspection
Tubeless system check and sealant top-up (if applicable)

Clean & Finish:
Drivetrain clean and re-lubrication
Full wipe-down and final inspection

Important Information:
This service does not include brake bleeding, suspension servicing, or internal bearing work
Any worn components or additional work will be identified and discussed before proceeding

Designed to keep your bike running efficiently and reliably — smooth, quiet, and ready for every ride

Interim Service - Road/Gravel

A comprehensive annual service designed to restore your e-bike to peak condition.

This is a full mechanical refresh — not just adjustment. Key components are removed, cleaned, serviced, and reassembled to ensure long-term performance, reliability, and a smooth, quiet ride.

Includes everything in the Interim Service, plus a deeper level of mechanical work and system inspection specific to e-bikes.

What’s Included:

Deep Mechanical Service:
Full drivetrain strip, clean, and rebuild
Gear inner and outer cables replaced (where applicable)
Bottom bracket removed, cleaned, and re-greased
Headset removed, cleaned, and re-greased

Advanced Brake Service:
Full hydraulic brake bleed (front and rear)
Brake system reset and performance optimisation

Frame & Chassis Overhaul:
Frame strip-down and deep clean
Suspension linkage inspection and service (where applicable)
Bearing condition check across key areas

Wheel & Tyre Setup:
Wheels trued and tension checked
Tyres removed and tubeless system refreshed

E-Bike System Checks:
Motor area cleaned and inspected
Battery mount and connections checked
Wiring and routing inspected
System check via diagnostic tools (where applicable)

Additional Components:
Dropper post serviced or cable replaced
Full system reassembly with torque check

Important Information:
Suspension servicing (fork and shock internals) is not included but can be added
Replacement parts are not included in the service price
Any additional work or parts will always be discussed before proceeding

This is the service that makes your e-bike feel right again — smoother, quieter, and performing exactly as it should.

Full Service - E-MTB

Update electronic drivetrain firmware

Charge/replace electronic drivetrain batteries

Clean and inspect bottom bracket shell threads if appropriate

Inspect and regrease pedal/crankarm threads

Inspect / adjust suspension linkages (if required)

Install crankset, ensure smooth running/no play

Full drivetrain strip, degrease and re-lubrication

A comprehensive annual service designed to restore your bike to peak condition.

This is a full mechanical refresh — not just adjustment. Key components are removed, cleaned, serviced, and reassembled to ensure long-term performance, reliability, and a smooth, quiet ride on the trail.

Includes everything in the Interim Service, plus a deeper level of mechanical work to bring your bike back to a true “like-new” feel.

What’s Included:

Deep Mechanical Service:
Full drivetrain strip, clean, and rebuild
Gear inner and outer cables replaced (where applicable)
Bottom bracket removed, cleaned, and re-greased
Headset removed, cleaned, and re-greased

Advanced Brake Service:
Full hydraulic brake bleed (front and rear)
Brake system reset and performance optimisation

Frame & Chassis Overhaul:
Frame strip-down and deep clean
Suspension linkage inspection and service (where applicable)
Bearing condition check across key areas

Wheel & Tyre Setup:
Wheels trued and tension checked
Tyres removed and tubeless system refreshed

Additional Components:
Dropper post serviced or cable replaced
Full system reassembly with torque check

Important Information:
Suspension servicing (fork and shock internals) is not included but can be added
Replacement parts are not included in the service price
Any additional work or parts will always be discussed before proceeding

This is the service that brings your bike back to life — smoother, quieter, and performing exactly as it should on the trail.

Full Service - Analog MTB

A comprehensive annual service designed to restore your bike to peak condition.

This is a full mechanical refresh — not just adjustment. Key components are removed, cleaned, serviced, and reassembled to ensure optimal efficiency, reliability, and a smooth, quiet ride.

Includes everything in the Interim Service, plus a deeper level of mechanical work to bring your bike back to a true “like-new” feel.

What’s Included:

Deep Mechanical Service:
Full drivetrain strip, clean, and rebuild
Gear inner and outer cables replaced (where applicable)
Bottom bracket removed, cleaned, and re-greased
Headset removed, cleaned, and re-greased

Advanced Brake Service:
Full hydraulic brake bleed (where applicable)
Brake system reset and performance optimisation

Frame & Component Overhaul:
Frame strip-down and deep clean
Bearing condition check across key areas

Wheel & Tyre Setup:
Wheels trued and tension checked
Tyres removed and tubeless system refreshed (if applicable)

Additional Components:
Full system reassembly with torque check
Final setup and performance check

Important Information:
Replacement parts are not included in the service price
Any additional work or parts will always be discussed before proceeding

This is the service that restores how your bike should feel — smooth, efficient, and performing exactly as intended.

Full Service - Gravel/Road

Suspension Servicing

A routine suspension service designed to maintain fork performance, sensitivity, and long-term reliability.

This service refreshes lubrication, removes contamination, and ensures all lower-leg components are functioning correctly in line with manufacturer service intervals.

Ideal as preventative maintenance to keep your fork performing consistently between full services.

What’s Included:
Fork removed from bike
Lower legs removed and fully cleaned
Bath oil replaced
Inspection of bushings, seals, and internal surfaces
Reassembly to manufacturer specification
Function check and setup

Important Information:
Suitable for RockShox and Fox forks
Wiper seals and foam rings are not included (cost varies by model)
Any additional parts will be discussed prior to fitting

Recommended For:
Regular riders (every 30–50 hours)
Bikes used in wet, muddy, or dusty conditions
Riders noticing reduced small-bump sensitivity
Preventative maintenance to reduce long-term wear

All work is carried out using manufacturer-recommended procedures and fluids.

Fork Lower Leg Service (30–50 Hours) - Interim Service

Fork removal and reinstallation

A routine suspension service designed to maintain rear shock performance, sensitivity, and long-term reliability.

This service focuses on the air spring side of the shock, refreshing lubrication, removing contamination, and ensuring smooth and consistent operation in line with manufacturer service intervals.

Ideal as preventative maintenance to keep your suspension performing as it should between full services.

What’s Included:
Rear shock removed and refitted
Air can stripped and internally cleaned
Air can lubricants replaced
Inspection of seals and internal components
Reassembly to manufacturer specification
Function check and setup

Important Information:
Suitable for RockShox and Fox rear shocks
Air can seal kits are not included (cost varies by model)
Any additional parts or work will be discussed prior to fitting

Recommended For:
Regular riders (every 30-50 hours depending on conditions)
Bikes used in wet, muddy, or dusty environments
Riders noticing reduced sensitivity or inconsistent performance
Preventative maintenance to extend shock lifespan

All work is carried out using manufacturer-recommended procedures and fluids.

Rear Shock Air Can Service (50 Hour) - Interim Service

Rear shock removal and reinstallation

A comprehensive suspension service designed to restore both fork and rear shock to optimal performance in line with manufacturer-recommended 200-hour service intervals.

This service goes beyond routine maintenance, combining full lower-leg and air can servicing with deeper inspection and coordination of advanced internal servicing where required.

Ideal for riders who use their bike regularly, ride in demanding conditions, or want their suspension performing at its highest level.

What’s Included:

Fork:
Fork removed from bike
Lower leg service (full strip, clean, lubrication refresh)
Inspection of bushings, seals, and internal surfaces

Rear Shock:
Shock removed from bike
Air can service (strip, clean, lubrication refresh)
Inspection of seals and air spring components
System Check & Setup
Reassembly to manufacturer specification
Full function check and setup
Sag and basic setup reset (if required)
Advanced Servicing (Important Section)

Where required, we will advise on:
Full damper service
Seal head replacement
Internal rebuilds

These are not included as standard and may be carried out in-house or via specialist partners depending on the model.

Important Information:
Suitable for Fox and RockShox suspension systems
Seal kits and internal parts are not included
Any additional work will always be discussed prior to proceeding

Recommended For:
Riders approaching or exceeding 150–200 hours of riding
Bikes that feel inconsistent, harsh, or lacking sensitivity
Annual suspension refresh
Riders wanting maximum performance and longevity

All work is carried out using manufacturer-recommended procedures and fluids.

Full Suspension Service (Fork & Shock 200 Hour)

A comprehensive fork service designed to restore performance, consistency, and reliability in line with manufacturer-recommended 200-hour service intervals.

This service includes a full lower leg service and deeper internal inspection, with coordination of advanced damper servicing where required.

Ideal for riders who use their bike regularly or want their suspension performing at its highest level.

What’s Included:
Fork removed from bike
Lower leg service (full strip, clean, lubrication refresh)
Inspection of bushings, seals, and internal components
Reassembly to manufacturer specification
Full function check and setup
Advanced Servicing

Where required, we will advise on:
Damper service
Seal head replacement
Internal rebuilds

These are not included as standard and may be carried out in-house or via specialist partners depending on the fork.

Important Information
Suitable for Fox and RockShox forks
Seal kits and internal parts are not included
Any additional work will be discussed prior to proceeding

Full Fork Service (200 Hour)

A comprehensive rear shock service designed to restore performance, sensitivity, and reliability in line with manufacturer-recommended 200-hour service intervals.

This service includes a full air can service and deeper inspection, with coordination of advanced internal servicing where required.

Ideal for riders experiencing reduced performance or looking to maintain their suspension to a high standard.

What’s Included:
Rear shock removed from bike
Air can service (strip, clean, lubrication refresh)
Inspection of seals and internal components
Reassembly to manufacturer specification
Full function check and setup
Advanced Servicing

Where required, we will advise on:

Full damper service
Seal head replacement
Internal rebuilds

These are not included as standard and may be carried out in-house or via specialist partners depending on the model.

Important Information:
Suitable for Fox and RockShox rear shocks
Seal kits and internal parts are not included
Any additional work will be discussed prior to proceeding

Full Shock Service (200 Hour)

Diagnostic & EBike Support

Specialist Brose S motor belt replacement service for eMTBs fitted with the Brose S motor system.

This service is for bikes where the internal motor belt is worn, damaged, slipping, noisy or has failed completely. The price includes the required Brose service kit, motor removal from the bike, belt replacement, reassembly and labour.

Includes:

Removal of the motor from the bike
Opening and inspection of the motor belt area
Replacement of the internal drive belt
Installation of the service kit
Replacement of relevant gaskets/bolts included within the kit
Motor reinstallation
Basic system and function check after completion

This service covers the Brose S belt replacement only. It does not include replacement bearings, electronic repairs, wiring faults, motor diagnostics beyond the belt replacement process, or any additional damage found once the motor is removed or inspected.

If further issues are found, we will contact you before carrying out any additional work.

Brose S Motor Belt Replacement Service

A professional diagnostic service for e-bikes experiencing faults, error codes, or performance issues.

Using manufacturer-approved software, we connect directly to your system to identify faults, assess system health, and provide clear recommendations before any repair work is carried out.

What’s Included:
Electronic Diagnostics
Connection to manufacturer diagnostic software
Fault codes read and logged
Firmware checked and updated where applicable*
Service indicators reset where appropriate*
Digital diagnostic report generated

*Supported on Bosch, Shimano, TQ, and Fazua systems

Initial Mechanical Assessment:
Visual inspection of motor, battery, and wiring
Basic safety check of key components
Assessment of likely cause and recommended next steps

Important Information:
This is a diagnostic-only service and does not include repairs
Diagnostic time is chargeable regardless of outcome
Any required repair or servicing will be quoted separately
Findings will be used to guide any follow-on work

Recommended For:
Fault codes or warning messages
Power loss or intermittent assistance
Battery or motor concerns
Pre-repair assessment before committing to further work

All diagnostics are carried out using manufacturer-approved software and procedures.

E-Bike Diagnostics

A professional labour-only service for the removal and replacement of an e-bike motor.

This service is intended for customers who already have a compatible replacement motor supplied or approved by the manufacturer. All work is carried out using manufacturer-approved procedures to ensure correct installation, alignment, and system function.

What’s Included:
Motor Removal & Installation
Existing motor removed from the frame
Replacement motor installed and correctly aligned
Mounting interfaces cleaned and prepared
All fixings torqued to manufacturer specifications
Electrical & System Checks
Wiring connections inspected and secured
System connected to diagnostic software
Firmware checked and updated where applicable*
System function test carried out

*Supported on Bosch, Shimano, TQ, and Fazua systems

Important Information:
Labour-only service – motor not supplied
Replacement motor must be compatible and approved for the bike
This service does not include fault diagnosis or warranty processing
Additional mechanical or electrical work is not included
Any additional work will be discussed prior to proceeding

Recommended For:
Warranty or insurance motor replacements
Customers with manufacturer-supplied replacement motors
Approved motor swaps requiring professional installation


All work is carried out using manufacturer-approved tools, procedures, and torque specifications.

E-Bike Motor Replacement (Labour Only)

Performance Setup & Suspension Tuning

A rider-specific setup session designed to dial in your bike for performance, comfort, and control.

This is not a standard setup. We work through your suspension, cockpit, and contact points to ensure the bike is balanced and performing correctly for how and where you ride.

Ideal for new bikes, upgraded components, or riders who feel their setup isn’t quite right and are struggling to get the "dialled" feel

What’s Included:
Rider and bike assessment
Suspension setup (sag, pressure, rebound, compression)
Fork and shock balance optimisation
Cockpit setup (bars, levers, saddle position)
Tyre pressure optimisation
Iterative adjustments during the session
Final setup recorded for future reference
Important Information
This is a setup and tuning session, not a mechanical service
Bike must be clean and in safe working order
Any mechanical issues will be identified before tuning begins

Optional Add-Ons:
Suspension servicing
Brake bleed
Tyre setup / upgrades
E-bike diagnostics

Frame Protection

A professional frame protection installation designed to protect your bike from wear, impact damage, and cosmetic deterioration — without compromising the look or finish.

This is a precision service, focused on clean application, accurate alignment, and a high-quality finish that holds up over time.

For the best results, this service is ideally carried out on new or near-new bikes before regular riding.

What’s Included:
Full preparation of frame surfaces prior to installation
Professional installation of RideWrap or InvisiFrame protection kit
Accurate alignment and application of all protection panels
Careful trimming and finishing where required
Final inspection to ensure correct adhesion and finish quality

Important Information:
Labour only — protection kits are not included unless supplied by Torque Collective
For best results, bikes should be new or in near-new condition
The bike must arrive clean and free from dirt, grease, or contamination
If cleaning is required prior to installation, this will be discussed and charged separately
Used bikes can be wrapped, however existing marks or imperfections may remain visible beneath the film

A clean, professionally installed finish that protects your bike properly — not just covers it.

RideWrap / InvisiFrame Installation

Bearing Services

Your suspension pivots are critical to how your bike rides. Over time, dirt, moisture, and heavy use can cause pivot bearings to wear, seize, or develop play—leading to poor suspension performance, unwanted noise, and accelerated frame wear.

Our Frame Pivot Bearing Service includes a full strip-down of the suspension linkage and pivot system, allowing us to inspect, clean, service, and restore smooth suspension movement throughout the rear end of the bike.

Ideal for bikes showing creaking, stiffness, play through the rear suspension, or as part of preventative maintenance for hard-ridden MTB and e-MTB bikes.

This is a precision service designed to protect frame longevity and restore proper suspension performance.

What’s included:

Full removal of rear suspension linkage and pivot hardware
Inspection of all pivot bearings, axles, spacers, and mounting hardware
Cleaning of all pivot interfaces and contact surfaces
Fresh grease and anti-seize application where required
Bearing condition assessment
Reassembly to manufacturer torque specifications
Suspension movement check and frame inspection
Hardware security and safety check

Notes:

Replacement bearings are charged separately if required
Severely worn, seized, or damaged hardware may require additional parts
Shock removal/refit included where required for correct access
Particularly recommended for e-MTBs and year-round riding conditions

Full Pivot Bearing Replacement

Smooth steering and precise front-end control start with a properly maintained headset. Our Headset Service includes full inspection, strip-down, cleaning, and re-greasing of your headset assembly to eliminate contamination, prevent premature bearing wear, and restore smooth operation.

Ideal for bikes exposed to regular wet weather, pressure washing, winter riding, or any bike showing signs of rough steering, knocking, creaking, or front-end play.

This service helps protect one of the most overlooked but important contact points on your bike—keeping your front end quiet, smooth, and reliable.

What’s included:

Removal of fork and headset components
Full inspection of bearings, cups, crown race, and contact surfaces
Cleaning and contamination removal
Fresh high-quality grease application
Reassembly to correct preload and torque settings
Stem and cockpit alignment check
Steering function and safety inspection

Notes:

Replacement bearings, crown races, or damaged components are charged separately
Any wear or corrosion found during inspection will be advised before additional work proceeds
Particularly recommended for MTB and e-MTB bikes ridden year-round

Headset Service

Smooth, properly maintained hub bearings are essential for rolling efficiency, wheel longevity, and precise bike handling. Worn, dry, or contaminated bearings can cause rough rotation, play through the wheel, poor engagement feel, and premature hub wear.

Our Wheel Bearing Service includes full inspection, strip-down where required, cleaning, servicing, and reassembly of your hub system to restore smooth performance and ensure everything is running exactly as it should.

Ideal for MTB and e-MTB bikes ridden year-round, wet weather bikes, or any wheel showing rough bearings, side-to-side play, noise, or poor freehub performance.

This service helps protect expensive wheelsets and keeps your bike feeling fast, quiet, and mechanically precise.

What’s included:

Wheel removal and full hub inspection
Bearing condition assessment
Hub strip-down where serviceable
Cleaning of bearings, freehub body, and internal interfaces
Fresh grease and lubrication where appropriate
Axle, end cap, and spacer inspection
Freehub engagement and function check
Reassembly to correct preload and torque settings
Final wheel spin, play, and safety inspection

Notes:

Replacement bearings, pawls, springs, seals, or freehub parts are charged separately
Some sealed cartridge systems require full bearing replacement rather than service
Hub design varies by manufacturer and may affect labour time
Covers single wheel unless otherwise specified

Wheel Bearing Service

Brakes, Dropper Posts & Controls

Professional installation of a new hydraulic brake system, including internal hose routing where required and a full brake bleed to ensure reliable lever feel and consistent stopping power.

This service is ideal when fitting new front and/or rear brakes, upgrading to a higher-performance brake system, replacing worn or damaged brakes, or converting to a different brake brand or model.

Includes:
Removal of old brake system
Installation of new brake lever, hose and caliper
Internal frame routing where applicable
Hose shortening and correct fitting of barb/olive or manufacturer-specific fittings
Full hydraulic brake bleed
Caliper alignment
Basic bedding-in check
Safety inspection before handover

Please note:
Brake pads, rotors, adaptors, mounts, olives, barbs, hose kits or brake fluid are not included unless supplied with the brake system or purchased separately. Some internally routed frames, e-bikes or integrated cockpit systems may require additional labour.

Installation of New Brakes — Including Bleed & Internal Routing

Brake Bleed (One Brake Only)

A hydraulic brake bleed service designed to restore consistent lever feel and reliable braking performance.

This service removes air from the system and refreshes brake fluid where required, ensuring both brakes are operating as they should.

What’s Included:
Hydraulic bleed of front and rear brakes
Removal of air from brake lines
Brake fluid refreshed where applicable
Lever feel and brake performance check

Important Information:
Price covers both brakes
Suitable for hydraulic disc brake systems only
Pad replacement, rotor truing, and calliper alignment are not included
Any additional work will be discussed prior to proceeding

Recommended For:
Spongy or inconsistent lever feel
Reduced braking performance
Routine hydraulic brake maintenance
Bikes requiring a system refresh

Brake Bleed (Front & Rear)

An internal service for cartridge-based dropper posts designed to restore smooth operation, consistent return speed, and reliable performance.

This service addresses issues within the cartridge itself and is recommended where cable replacement alone has not resolved performance problems.

What’s Included:
Dropper post removed and refitted (if required)
Internal cartridge removed and inspected
Cartridge serviced or replaced where applicable
Post cleaned and reassembled
Function and return speed checked

Important Information:
Suitable for cable-actuated, cartridge-based dropper posts
Hydraulic droppers (e.g. RockShox Reverb) are not included
Replacement cartridges or internal parts are not included
Additional labour may apply if linkage or shock removal is required
Any additional work will be discussed prior to proceeding

Recommended For:
Slow or inconsistent return
Posts not holding position correctly
Issues not resolved by cable replacement
Riders wanting reliable dropper performance restored

All work is carried out using manufacturer-recommended procedures and appropriate lubricants.

Dropper Post Cartridge Service

A comprehensive brake service designed to restore braking performance, consistency, and reliability.

This service involves a full strip, clean, and rebuild of the brake system, addressing contamination, wear, and performance issues that cannot be resolved with a standard bleed alone.

Ideal for bikes with inconsistent braking, poor lever feel, or systems that have seen heavy use.

What’s Included:
Removal of front and rear brake systems (where required)
Full strip and clean of brake calipers
Inspection and cleaning of pistons and seals
Lever inspection and basic service (where applicable)
Replacement of inner cables (where applicable for cable systems)
Full hydraulic bleed with fresh fluid
Reinstallation and system setup
Brake performance and lever feel check

Important Information:
Suitable for hydraulic and cable-actuated disc brake systems
Brake pads, rotors, and replacement parts are not included
Heavily worn or damaged components may require replacement
Some brake models have limited serviceable internal parts
Any additional work will be discussed prior to proceeding

Recommended For:
Inconsistent or poor braking performance
Contaminated or neglected brake systems
Sticky or slow-return pistons
Bikes used regularly in wet or harsh conditions
Riders wanting maximum braking confidence

All work is carried out using manufacturer-recommended procedures and fluids.

Full Brake Service (Front & Rear)

Fine-tuning your cockpit or replacing a worn or damaged hose? This service covers the adjustment or full replacement of a single hydraulic brake hose to ensure optimal routing, clean aesthetics, and consistent braking performance.

Whether you're shortening an overlong hose for a cleaner setup, or installing a new hose entirely, we’ll ensure correct routing, secure connections, and a professional finish throughout.

What’s included:

Removal of existing hose (if required)
Hose shortening or full replacement (single brake)
Installation of new fittings (olive/barb where required)
Correct routing and securing to frame
Full hydraulic bleed using manufacturer-specific fluid
Brake function check and safety inspection

Notes:

Replacement hose, olives, barbs, and fittings are charged separately
Covers either front or rear brake

Brake Hose Adjustment / Replacement (Single)

For a full cockpit refresh or complete brake system overhaul, this service covers adjustment or replacement of both front and rear hydraulic brake hoses.

Ideal for new builds, bar upgrades, or bikes requiring a full hose refresh—ensuring consistent performance, clean routing, and a balanced braking feel front to rear.

What’s included:

Removal of existing hoses (if required)
Hose shortening or full replacement (front and rear)
Installation of new fittings (olives/barbs where required)
Correct routing and securing to frame
Full hydraulic bleed on both brakes using manufacturer-specific fluid
Brake function check and safety inspection

Notes:

Replacement hoses, olives, barbs, and fittings are charged separately
Includes both front and rear brakes

Brake Hose Adjustment / Replacement (Pair)

Fresh brake pads are essential for consistent braking power, proper modulation, and rotor protection. Worn, contaminated, or glazed pads can cause poor stopping performance, excessive noise, vibration, and unnecessary rotor wear.

Our Brake Pad Replacement service ensures your braking system is inspected, correctly fitted, and performing exactly as it should—whether you’re replacing worn pads after heavy riding or upgrading to a more suitable compound for your riding style.

Ideal for MTB, e-MTB, gravel, and road riders who demand reliable braking performance in all conditions.

We’ll assess pad wear, rotor condition, and overall brake function to make sure the system is safe and working properly.

What’s included:

Removal of old brake pads
Brake caliper inspection
Piston inspection and reset
Rotor wear and contamination check
Installation of new brake pads
Brake alignment check
Brake bed-in preparation guidance
Final brake function and safety inspection

Notes:

Brake pads are charged separately unless supplied by customer
Severely contaminated rotors or sticking pistons may require additional service
Brake bleed not included unless required and booked separately
Covers either front or rear brake (pair option recommended for full replacement)

Brake Pad Replacement

Select what extras or individual services you offer. If you don’t have a set price, you can select "Price on request"

Workshop Add-Ons

Adjustment of cable or outer housing length for gear, mechanical brake or dropper post systems.

This service is for shortening or lengthening non-hydraulic cables, outers or housings where the current routing or length needs correcting. It is suitable when fitting new controls, tidying cockpit setup, changing bar/stem position, replacing a lever or remote, or correcting excess cable length.

Includes:

Shortening or lengthening gear, mechanical brake or dropper cable/housing
Replacement or adjustment of inner cable and/or outer housing where required
Cable end finishing
Basic function check after adjustment

Please note:
This service does not include hydraulic brake hose shortening, brake bleeding, gear indexing, drivetrain tuning, dropper post servicing or internal routing unless agreed separately.

Any replacement cables, outers, ferrules or small parts are not included unless supplied or purchased separately.

Cable / Hose Length Adjustment — Non-Hydraulic

Dropper Post Install

A precision installation service for internally routed cables and hoses, ensuring clean routing, correct function, and a rattle-free finish.

Internal routing requires additional time, care, and attention compared to external systems. This service is carried out using the correct tools and techniques to ensure smooth operation and a professional result.

What’s Included:
Removal of existing internal cable or hose (where applicable)
Installation and routing of new cable or hose through the frame
Secure internal cable management to prevent rattle or interference
Correct setup, tensioning, and function check

Important Information:
Price is per cable or hose
Labour only — cables, hoses, and fittings are not included
Hydraulic hose cutting and brake bleeding are not included and charged separately if required
More complex systems (integrated cockpits, e-bikes, or difficult routing) may require additional labour
Any additional work will always be discussed before proceeding

Clean routing, correct function, and a finish that looks and feels as it should.

Internal Routed Cabling

A precision alignment service to ensure your handlebars and front wheel are perfectly aligned for accurate tracking and confident handling.

Using a laser alignment tool, we correct subtle misalignment that can occur after transport, crashes, or component changes — something that is often difficult to identify by eye alone.

What’s Included:
Laser alignment of handlebars and front wheel
Stem and cockpit alignment adjustment
Final alignment and function check

Important Information:
Suitable for all bike types
Alignment service only — does not include component replacement or mechanical repair

Laser Handlebar Alignment

A clean drivetrain is essential for smooth shifting, efficient power transfer, and long-term component life. Our Drivetrain Degrease & Refresh service is designed to remove built-up dirt, old lubricant, grit, and contamination from your transmission system—restoring performance and reducing unnecessary wear.

Ideal for bikes that have seen heavy winter use, wet riding conditions, or simply haven’t had a proper deep clean in some time.

This is far more than a quick wipe-down—we carefully clean the drivetrain properly to ensure your bike runs quieter, shifts cleaner, and performs as it should.

What’s included:

Full drivetrain inspection
Deep clean and degrease of chain
Cassette cleaning and contamination removal
Chainring cleaning
Derailleur jockey wheel clean
Rear derailleur inspection
Fresh lubrication applied with correct lubricant for riding conditions
Gear function check and shifting assessment

Notes:

Excessively worn components requiring replacement will be advised separately
Does not include drivetrain part replacement unless booked additionally
Ideal as part of regular servicing or performance preparation

Drivetrain Degrease & Refresh

For riders who want the cleanest, quietest, and most efficient drivetrain performance possible, our Chain Wax Service provides a full strip, deep clean, and hot wax treatment designed to reduce friction, improve longevity, and keep your transmission running exceptionally smoothly.

Unlike traditional wet lubricants that attract dirt and contamination, waxed chains run cleaner, stay quieter, and significantly reduce drivetrain wear—making this a premium upgrade for performance-focused riders, year-round riders, and high-value drivetrains.

Ideal for MTB, gravel, road, and e-MTB riders looking for maximum drivetrain efficiency and reduced maintenance between rides.

This is a workshop-prepared service using proper degreasing and full wax preparation—not simply applying drip wax over old lubricant.

What’s included:

Full chain removal
Complete degreasing and contamination removal
Drivetrain inspection for wear and condition
Hot wax immersion treatment using premium chain wax
Correct curing and final preparation
Chain refit and drivetrain function check
Shifting inspection and performance check

Notes:

Designed for chains in good serviceable condition
Excessively worn chains requiring replacement will be advised separately
Initial wax conversion requires full stripping of previous lubricants for best results
Best results achieved with ongoing wax maintenance and repeat treatments

Chain Wax Service

A worn, dry, contaminated, or poorly fitted bottom bracket can cause creaking, rough pedalling, poor drivetrain feel, and accelerated wear through the crank and frame interface.

Our Bottom Bracket Service / Replacement covers the inspection, removal, cleaning, preparation, and refitting or replacement of your bottom bracket to restore smooth, quiet, and reliable performance.

This service is ideal if you are experiencing creaks under load, rough bearing feel, lateral play, or if your bottom bracket is due for routine maintenance.

What’s included:

Crankset removal
Bottom bracket inspection
Bottom bracket removal where required
Frame shell / interface cleaning
Thread, press-fit, or bearing interface inspection
Grease / anti-seize / retaining compound applied where appropriate
Bottom bracket refit or replacement
Crankset refit and torque check
Drivetrain function check
Final creak and safety inspection

Notes:

Replacement bottom brackets are charged separately
Severely seized or damaged components may require additional labour
Press-fit systems may require additional assessment depending on condition
Not all creaks originate from the bottom bracket; further diagnosis may be required if noise remains after service

Bottom Bracket Service / Replacement

Crisp, accurate shifting depends on correct cable tension, clean routing, and precise drivetrain adjustment. Poor indexing, contaminated cables, or worn housing can cause missed shifts, ghost shifting, noisy drivetrains, and unnecessary drivetrain wear.

Our Gear Indexing & Cable Service is designed to restore smooth, reliable shifting by diagnosing drivetrain issues, adjusting derailleur setup, and replacing inner cables or housing where required.

Ideal for bikes suffering from poor shifting performance, new bike setups, post-crash adjustments, or routine maintenance on mechanical drivetrains.

Whether it’s a simple indexing adjustment or a full cable refresh, we ensure your drivetrain performs exactly as it should.

What’s included:

Full drivetrain and shifting inspection
Rear derailleur alignment and function check
Gear indexing and adjustment
Limit screw and B-gap assessment where applicable
Cable tension optimisation
Inner gear cable replacement where required
Outer housing inspection and replacement if needed
Gear function test across full cassette range
Final shifting and safety check

Notes:

Replacement cables, housing, ferrules, and small parts are charged separately
Hanger alignment or replacement is charged separately if required
Covers mechanical drivetrains only (not electronic systems such as AXS or Di2)
Excessively worn drivetrains may require cassette, chain, or chainring replacement for correct shifting performance

Gear Indexing & Cable Service

Whether it’s a brand-new frame build, a premium component upgrade, or a complete dream-bike project, our Full Bike Build / Custom Build service is designed for riders who want absolute attention to detail and workshop-level precision from the very first ride.

This is far more than basic assembly. Every component is carefully installed, torqued, aligned, and checked to ensure your bike performs exactly as intended—clean, quiet, reliable, and built properly from the ground up.

Ideal for custom MTB and e-MTB builds, premium frame swaps, high-end component upgrades, race bikes, and rider-specific performance setups.

At Torque Collective, this is where our premium workshop approach really shows—precision, detail, and no shortcuts.

What’s included:

Full bike assembly from frame or boxed bike
Headset, bottom bracket, drivetrain, cockpit, and brake installation
Internal routing where required
Brake setup and hydraulic bleed where applicable
Gear setup and indexing
Suspension setup baseline
Wheel installation and alignment checks
Torque check across full build
Final safety inspection
Test ride and function check where appropriate

Notes:

Parts and consumables charged separately
Build complexity varies significantly depending on specification
e-MTB motor installs or advanced electronic setup may require additional labour
Custom wheel builds quoted separately where required
Full suspension tuning sessions can be added separately for rider-specific setup

Request to book

Request to book

Add your bike and choose your services, choose your drop-off/collection date and then provide your contact details. It's as easy as that!

Booking type

Collection

Drop-off

Due today for collection

Due today for drop-off

Your bikes & services

No bikes found

Drop-off details

Drop-off date

Drop-off location (2 available)

Price details

No bikes found

Subtotal:
£0.00

VAT (20%)
£0.00

Est total:
£0.00

Due today:
£0.00

Your booking will be confirmed by the mechanic and you will be notified by your preferred contact method. If the booking is rejected payment will not be taken.

No bikes found

Subtotal:
£0.00

VAT (20%)
£0.00

Est total:
£0.00

Due today:
£0.00

Request to book

Request to book

Add your bike and choose your services, choose your drop-off/collection date and then provide your contact details. It's as easy as that!

Booking type

Collection

Drop-off

Due today for collection

Due today for drop-off

Your bikes & services

No bikes found

Drop-off details

Drop-off date

Drop-off location (2 available)

Price details

No bikes found

Subtotal:£0.00

VAT (20%)£0.00

Est total:£0.00

Due today:£0.00

Your booking will be confirmed by the mechanic and you will be notified by your preferred contact method. If the booking is rejected payment will not be taken.

No bikes found

Subtotal:£0.00

VAT (20%)£0.00

Est total:£0.00

Due today:£0.00

Subtotal:
£0.00

VAT (20%)
£0.00

Est total:
£0.00

Due today:
£0.00

Subtotal:
£0.00

VAT (20%)
£0.00

Est total:
£0.00

Due today:
£0.00